3,777
edits
GHA-15: Difference between revisions
Jump to navigation
Jump to search
m
→Threads
m (→Notepad) |
m (→Threads) |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 12: | Line 12: | ||
* [https://vansairforce.net/community/showthread.php?t=218681 VAF] | * [https://vansairforce.net/community/showthread.php?t=218681 VAF] | ||
* [https://www.facebook.com/groups/vansrv10/posts/6340273269427052 FB] | * [https://www.facebook.com/groups/vansrv10/posts/6340273269427052 FB] | ||
* [https://www.facebook.com/groups/vansrv10/posts/6997949003659472 FB] | |||
==== Installation Manual ==== | ==== Installation Manual ==== | ||
| Line 19: | Line 20: | ||
[[File:Screen Shot 2023-10-21 at 4.03.53 PM.png|400x400px]]<br>Connector | [[File:Screen Shot 2023-10-21 at 4.03.53 PM.png|400x400px]]<br>Connector | ||
* Note: unlike with D-Sub connectors, each pin needs at least 5/8 inch of plain wire (22 AWG or thinner) before thickening up for example for a splice or shielding. The distance between the end of the pin and where the wire exists the rubber gasket through a tiny hole is quite long. | * Note: unlike with D-Sub connectors, each pin needs at least 5/8 inch of plain wire (22 AWG or thinner) before thickening up for example for a splice or shielding. The distance between the end of the pin and where the wire exists the rubber gasket through a tiny hole is quite long. | ||
* Note: on the rubbery back side of the connector, the printed "1" seems to be closer to the hole to the left of the "1", but pin 1 is to the right of the "1".<br>The center pin 22 is a bit off-center to the bottom. Together with hole straight below it, they constitute the vertical center axis of the connector. At the two circles above, the center axis splits between 21/15 and 14/1. At the outermost circle | * Note: on the rubbery back side of the connector, the printed "1" seems to be closer to the hole to the left of the "1", but pin 1 is to the right of the "1".<br>The center pin 22 is a bit off-center to the bottom. Together with hole straight below it, they constitute the vertical center axis of the connector. At the two circles above, the center axis splits between 21/15 and 14/1. At the outermost circle at the bottom, it splits between 7/8. The 4 holes above 22 are almost in a perfect square pattern.<br>[[File:Screen Shot 2023-10-22 at 10.47.20 PM.png|300x300px]]<br>On the (hard) back-end of the connector, the numbers are printed in a way that the "1" is actually closer to pin "1".<br>[[File:Screen Shot 2023-10-21 at 3.36.20 PM.png|331x331px]]<br>(as seen from the back of the connector where you insert the pins through the silicone seals. The 9 o-clock position of this connector points forward in direction of flight.) | ||
==== Screw Torque ==== | ==== Screw Torque ==== | ||
| Line 32: | Line 33: | ||
* Optional: Suitable 10ft USB-C to USB-B laptop cable [https://www.amazon.com/gp/product/B082HQ3LP2 at Amazon] | * Optional: Suitable 10ft USB-C to USB-B laptop cable [https://www.amazon.com/gp/product/B082HQ3LP2 at Amazon] | ||
* Optional: Alodine pen to treat unpainted skin that will end up under the antenna: [https://www.aircraftspruce.com/catalog/cspages/touchprep.php?clickkey=92623 at Spruce].<br>[[File:2023-10-14 16-57-16.jpg|300x300px]] | * Optional: Alodine pen to treat unpainted skin that will end up under the antenna: [https://www.aircraftspruce.com/catalog/cspages/touchprep.php?clickkey=92623 at Spruce].<br>[[File:2023-10-14 16-57-16.jpg|300x300px]] | ||
====Debug Data==== | |||
Garmin hasn't yet released a USB-driver for the GHA-15. However, after plugging the USB cable into a laptop, a new device enumerates named GHA-15 and the details show the serial number of the device which is proof enough that two-way communication can be established. | |||
[[File:Screen Shot 2023-11-06 at 6.29.08 PM.png|300x300px]] | |||
====FCC Report==== | ====FCC Report==== | ||
*[https://fccid.io/IPH-04099 FCC Record] | *[https://fccid.io/IPH-04099 FCC Record] | ||