SECTION 6: VERTICAL STABILIZER: Difference between revisions
Jump to navigation
Jump to search
No edit summary |
No edit summary |
||
| Line 1: | Line 1: | ||
==== Builder Videos ==== | |||
Jason Ellis: | |||
*[https://www.youtube.com/watch?v=phIxaSNZFHc 6-2 Step 1 and 2] | |||
*[https://www.youtube.com/watch?v=n59BCJTVenI 6-2 Step 3] | |||
*[https://www.youtube.com/watch?v=7S_6nuWEFck 6-3 Step 1-3] | |||
*[https://www.youtube.com/watch?v=_6xIjO35mv4 6-3 Step 4-5] | |||
*[https://www.youtube.com/watch?v=7cNhu1i7sQ0 6-3 Step 6-7] | |||
*[https://www.youtube.com/watch?v=SzLayLMPUMg 6-3 Step 8-11] | |||
*[https://www.youtube.com/watch?v=7XOEIig4ODA 6-4 Step 1-4] | |||
*[https://www.youtube.com/watch?v=JdnlNPsJwM4 6-4 Step 5-11] | |||
*[https://www.youtube.com/watch?v=N9_RxWjDvHk 6-5 Step 1-3] | |||
*[https://www.youtube.com/watch?v=ZuUES4VUCUU 6-6 Step 1-4] | |||
*[https://www.youtube.com/watch?v=gfCN35sLw08 6-6 Step 5-9] | |||
These ribs have been sanded a bit and the web was fluted at the tip trying to bring the flanges closer together, but it still wasn't enough. | ==== Notes ==== | ||
*When first putting the nose rib in, don't ram in in there and cleco. Be gentle, and it will probably need to be sanded down. Otherwise you will have "outtie" dents on the leading edge of your skin. | |||
*These ribs have been sanded a bit and the web was fluted at the tip trying to bring the flanges closer together, but it still wasn't enough. | |||
[[File:VertStabNoseRib.JPG|600x400px]] | [[File:VertStabNoseRib.JPG|600x400px]] | ||
Before you start riveting, put some electrical tape on your bucking bar. It will help to not beat up the AlClad or scratch off your primer if you did that. | *Before you start riveting, put some electrical tape on your bucking bar. It will help to not beat up the AlClad or scratch off your primer if you did that. | ||
[[File:VertStab.JPG|600x400px]] | [[File:VertStab.JPG|600x400px]] | ||
Revision as of 17:01, 23 March 2022
Builder Videos
Jason Ellis:
- 6-2 Step 1 and 2
- 6-2 Step 3
- 6-3 Step 1-3
- 6-3 Step 4-5
- 6-3 Step 6-7
- 6-3 Step 8-11
- 6-4 Step 1-4
- 6-4 Step 5-11
- 6-5 Step 1-3
- 6-6 Step 1-4
- 6-6 Step 5-9
Notes
- When first putting the nose rib in, don't ram in in there and cleco. Be gentle, and it will probably need to be sanded down. Otherwise you will have "outtie" dents on the leading edge of your skin.
- These ribs have been sanded a bit and the web was fluted at the tip trying to bring the flanges closer together, but it still wasn't enough.
- Before you start riveting, put some electrical tape on your bucking bar. It will help to not beat up the AlClad or scratch off your primer if you did that.
