SECTION 50: CABIN HEAT AND VENTILLATION - Revision history

Martin: /* Page 50-3 */

2025-05-05T21:12:35Z

Page 50-3

← Older revision		Revision as of 21:12, 5 May 2025
Line 8:		Line 8:
	* When roughing up the skin in preparation for gluing the Naca vent in using tank sealant, take note that the glue contact area does not follow the opening of the skin all the way around. Towards the rear, the Naca vent extends, so mark the area up using the vent's outline.		* When roughing up the skin in preparation for gluing the Naca vent in using tank sealant, take note that the glue contact area does not follow the opening of the skin all the way around. Towards the rear, the Naca vent extends, so mark the area up using the vent's outline.
	* For stock panels, the needed closable eyeball vents are not part of the kit, consider ordering Van's part no "SV-6 Aluminum Air Vent". It comes in silver (clear) and black. You will need #8 bolts / washers / lock-nuts to mount them. Vans also offers a plastic version.		* For stock panels, the needed closable eyeball vents are not part of the kit, consider ordering Van's part no "SV-6 Aluminum Air Vent". It comes in silver (clear) and black. You will need #8 bolts / washers / lock-nuts to mount them. Vans also offers a plastic version.
			* Debris or insects may be blown into the cabin through the front fresh-air vents. Consider gluing in a piece of hardware cloth to filter the air stream.

Martin: /* Page 50-3 */

2025-05-05T21:10:37Z

Page 50-3

← Older revision		Revision as of 21:10, 5 May 2025
Line 6:		Line 6:
	==== Page 50-3 ====		==== Page 50-3 ====
	* The Naca vent that ships with the kit is a single piece consisting of the Naca vent itself and a glued-on rear extension that holds the eyeball vent outlet. For the stock panel, this is suitable as is, but for aftermarket panels with integrated support for a fresh air vent, you will need to cut the extension off and attach a duct tube. See the instructions for those aftermarket panels.		* The Naca vent that ships with the kit is a single piece consisting of the Naca vent itself and a glued-on rear extension that holds the eyeball vent outlet. For the stock panel, this is suitable as is, but for aftermarket panels with integrated support for a fresh air vent, you will need to cut the extension off and attach a duct tube. See the instructions for those aftermarket panels.
	* When roughing up the skin in preparation for gluing the Naca vent in using ~~tanke~~ sealant, take note that the glue contact area does not follow the opening of the skin all the way around. Towards the rear, the Naca vent extends, so mark the area up using the vent's outline.		* When roughing up the skin in preparation for gluing the Naca vent in using tank sealant, take note that the glue contact area does not follow the opening of the skin all the way around. Towards the rear, the Naca vent extends, so mark the area up using the vent's outline.
	* For stock panels, the needed closable eyeball vents are not part of the kit, consider ordering Van's part no "SV-6 Aluminum Air Vent". It comes in silver (clear) and black. You will need #8 bolts / washers / lock-nuts to mount them. Vans also offers a plastic version.		* For stock panels, the needed closable eyeball vents are not part of the kit, consider ordering Van's part no "SV-6 Aluminum Air Vent". It comes in silver (clear) and black. You will need #8 bolts / washers / lock-nuts to mount them. Vans also offers a plastic version.

Martin: /* Build Instruction Updates */

2025-05-05T21:09:56Z

Build Instruction Updates

← Older revision		Revision as of 21:09, 5 May 2025
Line 4:		Line 4:

	[[Category:Hints]]		[[Category:Hints]]
			==== Page 50-3 ====
			* The Naca vent that ships with the kit is a single piece consisting of the Naca vent itself and a glued-on rear extension that holds the eyeball vent outlet. For the stock panel, this is suitable as is, but for aftermarket panels with integrated support for a fresh air vent, you will need to cut the extension off and attach a duct tube. See the instructions for those aftermarket panels.
			* When roughing up the skin in preparation for gluing the Naca vent in using tanke sealant, take note that the glue contact area does not follow the opening of the skin all the way around. Towards the rear, the Naca vent extends, so mark the area up using the vent's outline.
			* For stock panels, the needed closable eyeball vents are not part of the kit, consider ordering Van's part no "SV-6 Aluminum Air Vent". It comes in silver (clear) and black. You will need #8 bolts / washers / lock-nuts to mount them. Vans also offers a plastic version.

Martin at 10:43, 23 November 2023

2023-11-23T10:43:23Z

← Older revision		Revision as of 10:43, 23 November 2023
Line 2:		Line 2:
	* N/A		* N/A
	Check for more recent updates [https://www.vansaircraft.com/service-information-and-revisions/?aircraft=rv-10&doctype=revisions-changes&sort=date here]		Check for more recent updates [https://www.vansaircraft.com/service-information-and-revisions/?aircraft=rv-10&doctype=revisions-changes&sort=date here]

			[[Category:Hints]]

Martin: Created page with "=== Build Instruction Updates === * N/A Check for more recent updates [https://www.vansaircraft.com/service-information-and-revisions/?aircraft=rv-10&doctype=revisions-changes&sort=date here]"

2022-06-12T06:14:57Z

Created page with "=== Build Instruction Updates === * N/A Check for more recent updates [https://www.vansaircraft.com/service-information-and-revisions/?aircraft=rv-10&doctype=revisions-changes&sort=date here]"

New page

=== Build Instruction Updates ===
* N/A
Check for more recent updates [https://www.vansaircraft.com/service-information-and-revisions/?aircraft=rv-10&doctype=revisions-changes&sort=date here]