SECTION 43: CABIN COVER - Revision history

Kirkbauer: /* Before You Start */

2025-08-28T19:16:52Z

Before You Start

← Older revision		Revision as of 19:16, 28 August 2025
Line 21:		Line 21:
	* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)		* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)
	* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top		* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top
			** If you do this now, you also probably want to install the Gas Strut Attach Brackets (or aftermarket alternatives) as described on page 45-16.
			** Note that the instructions are vague about the position of these brackets; if the outboard end is too high the door will hit the bracket when closed.
	* If interested in the [https://www.aerosportproducts.com/product/rv-10-door-sill-cap/ Aerosport Carbon Fiber Door Sills] now is a good time to order those.		* If interested in the [https://www.aerosportproducts.com/product/rv-10-door-sill-cap/ Aerosport Carbon Fiber Door Sills] now is a good time to order those.

Kirkbauer: /* Before You Start */

2025-08-18T14:03:58Z

Before You Start

← Older revision		Revision as of 14:03, 18 August 2025
Line 17:		Line 17:
	Modifications to Consider		Modifications to Consider

	* If you ~~will~~ be painting your interior~~, it may be easier to do an initial~~ painting of the cabin top ~~before attaching it (you'll need~~ to ~~touch it up later especially if you are using McMaster door seals; in that case perhaps just prime but don't paint). Note that when you start working on~~ the doors ~~you~~ will ~~need to either clamp them~~ to the ~~cabin top or some people prefer to drill temporary cleco holes~~. If you ~~prefer~~ the ~~latter then~~ you ~~may not want~~ to paint ~~until after~~ the ~~doors are done~~.		* If you are going to use McMaster door seals and are also going to be painting your cabin top, consider fully prepping the interior surface for paint but not priming or painting anything forward of the rear windows. Prepping is easier before the cabin top is attached but anything anywhere close to the doors will have a lot of work to do once the seals are finished.
			* If you are NOT using McMaster seals and ARE painting the cabin top, you should be able to fully prep, prime, and paint before attaching to the fuselage.
	* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)		* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)
	* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top		* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top

Kirkbauer: /* Before You Start */

2025-07-21T04:42:21Z

Before You Start

← Older revision		Revision as of 04:42, 21 July 2025
Line 17:		Line 17:
	Modifications to Consider		Modifications to Consider

	* If you will be painting your interior, it may be easier to do an initial painting of the cabin top before attaching it (you'll need to touch it up later). Note that when you start working on the doors you will need to either clamp them to the cabin top or some people prefer to drill temporary cleco holes. If you prefer the latter then you may not want to paint until after the doors are done.		* If you will be painting your interior, it may be easier to do an initial painting of the cabin top before attaching it (you'll need to touch it up later especially if you are using McMaster door seals; in that case perhaps just prime but don't paint). Note that when you start working on the doors you will need to either clamp them to the cabin top or some people prefer to drill temporary cleco holes. If you prefer the latter then you may not want to paint until after the doors are done.
	* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)		* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)
	* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top		* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top

Martin at 15:05, 6 July 2025

2025-07-06T15:05:44Z

← Older revision		Revision as of 15:05, 6 July 2025
Line 96:		Line 96:
	** If using the Aerosport Carbon Fiber Door Sills, consider installing them before doing this step. Trim them and put them into place, with the cut edge fitting under the radius where the cabin top sits on the door sill. Then apply the epoxy/filler as directed, permanently attaching the carbon fiber and covering the cut edge.		** If using the Aerosport Carbon Fiber Door Sills, consider installing them before doing this step. Trim them and put them into place, with the cut edge fitting under the radius where the cabin top sits on the door sill. Then apply the epoxy/filler as directed, permanently attaching the carbon fiber and covering the cut edge.

	[[~~index.php?title=~~Category:Hints]]		[[Category:Hints]]

Kirkbauer: /* Before You Start */

2025-07-06T14:52:26Z

Before You Start

← Older revision		Revision as of 14:52, 6 July 2025
Line 9:		Line 9:
	** Consider a good belt sander and plenty of replacement belts		** Consider a good belt sander and plenty of replacement belts
	** Use an angle-grinder or a die grinder with plenty of air supply -- consider diamond or masonry cutting discs		** Use an angle-grinder or a die grinder with plenty of air supply -- consider diamond or masonry cutting discs
			** If you don't have a lot of fresh epoxy go ahead and order a gallon for the cabin top plus doors.
	* Fiberglass Dust Protection		* Fiberglass Dust Protection
	** [https://www.uline.com/BL_1637/3M-Paint-Project-Respirators?keywords=3m+respirator 3M Respirator]		** [https://www.uline.com/BL_1637/3M-Paint-Project-Respirators?keywords=3m+respirator 3M Respirator]

Kirkbauer: Added info about Aerosport carbon fiber door sills

2025-07-05T15:41:59Z

Added info about Aerosport carbon fiber door sills

← Older revision		Revision as of 15:41, 5 July 2025
Line 19:		Line 19:
	* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)		* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)
	* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top		* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top
			* If interested in the [https://www.aerosportproducts.com/product/rv-10-door-sill-cap/ Aerosport Carbon Fiber Door Sills] now is a good time to order those.

	=== Resources ===		=== Resources ===
Line 91:		Line 92:
	* Step 1		* Step 1
	** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.		** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.
			* Step 2
			** If using the Aerosport Carbon Fiber Door Sills, consider installing them before doing this step. Trim them and put them into place, with the cut edge fitting under the radius where the cabin top sits on the door sill. Then apply the epoxy/filler as directed, permanently attaching the carbon fiber and covering the cut edge.

	[[index.php?title=Category:Hints]]		[[index.php?title=Category:Hints]]

Jasonbeall2002: /* Hints */

2025-06-13T20:34:11Z

Hints

← Older revision		Revision as of 20:34, 13 June 2025
Line 82:		Line 82:
	* Step 5		* Step 5
	** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.		** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.

			==== Page 43-11 ====

			* Step 3
			** These rivets will be inaccessible if you are bonding the Aerosport center roof console in prior to attaching the cabin top. Suggest installing these rivets BEFORE attaching the top.

	==== Page 43-12 Hardware ====		==== Page 43-12 Hardware ====
	* Step 1		* Step 1
	** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.		** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.
	[[Category:Hints]]		[[index.php?title=Category:Hints]]

Martin: /* Page 43-8 Center Strut and Windscreen */

2025-06-01T16:17:20Z

Page 43-8 Center Strut and Windscreen

← Older revision		Revision as of 16:17, 1 June 2025
Line 77:		Line 77:
	* Step 2		* Step 2
	** Note: The center rivet line on the F-1071 Forward Top skin is NOT center to the airplane! It is offset along with the F-1044A forward fuselage rib and the top center screw of the instrument panel. The center strut is attached to the rib's side.		** Note: The center rivet line on the F-1071 Forward Top skin is NOT center to the airplane! It is offset along with the F-1044A forward fuselage rib and the top center screw of the instrument panel. The center strut is attached to the rib's side.
			** Excessive thickness of the welds at the bottom end of the center cabin brace may prevent proper insertion down to the shim. Consider notching the skin to make it fit. Also consider whether you want cables to run down inside as they also need a skin opening. See also this [https://www.facebook.com/groups/vansrv10/posts/9793935377394140 FB post].
	* Step 4		* Step 4
	** Since you are drilling through steel guided by a pilot hole in the rib's web, best to first drill with a sharp 1/8 carbide drill bit, then upsize to #12		** Since you are drilling through steel guided by a pilot hole in the rib's web, best to first drill with a sharp 1/8 carbide drill bit, then upsize to #12
	* Step 5		* Step 5
	** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.		** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.

	==== Page 43-12 Hardware ====		==== Page 43-12 Hardware ====
	* Step 1		* Step 1
	** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.		** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.
	[[Category:Hints]]		[[Category:Hints]]

Martin: /* Page 43-8 Center Strut and Windscreen */

2025-05-14T03:30:12Z

Page 43-8 Center Strut and Windscreen

← Older revision		Revision as of 03:30, 14 May 2025
Line 81:		Line 81:
	* Step 5		* Step 5
	** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.		** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.
	[[~~index.php?title=~~Category:Hints]]		==== Page 43-12 Hardware ====
			* Step 1
			** On the forward door post, the longer 10R14 bolts go into the 3 upper holes, the shorter 10R11 ones go into the lower 5 holes.
			[[Category:Hints]]

Kirkbauer: Added overhead console photo.

2025-04-23T16:36:23Z

Added overhead console photo.

← Older revision		Revision as of 16:36, 23 April 2025
Line 16:		Line 16:
	Modifications to Consider		Modifications to Consider

	* If you will be painting your interior, it may be easier to do an initial painting of the cabin top before attaching it (you'll need to touch it up later)		* If you will be painting your interior, it may be easier to do an initial painting of the cabin top before attaching it (you'll need to touch it up later). Note that when you start working on the doors you will need to either clamp them to the cabin top or some people prefer to drill temporary cleco holes. If you prefer the latter then you may not want to paint until after the doors are done.
	* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)		* Some people run conduit for wires up the pillars on either side of the windscreen -- you'll want to do that before permanently attaching the cabin top (other people just run wires up the center support bar instead)
	* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top		* If installing an [https://www.aerosportproducts.com/product/rv-10-carbon-fiber-overhead-console/ AeroSport Overhead Console] it will be easier to fit and attach it before attaching the cabin top
Line 60:		Line 60:
	*** [https://www.panamericantool.com/novar-pencil-grinder.html Pencil grinder]		*** [https://www.panamericantool.com/novar-pencil-grinder.html Pencil grinder]
	*** [https://www.homedepot.com/p/Dremel-1-1-4-in-Rotary-Tool-Carbide-Cutting-Shaping-Wheel-for-Use-on-Woods-Fiberglass-Plastics-and-Laminates-543/202315728 Dremel Cutting / Shaping Wheel] (You will need more than one)		*** [https://www.homedepot.com/p/Dremel-1-1-4-in-Rotary-Tool-Carbide-Cutting-Shaping-Wheel-for-Use-on-Woods-Fiberglass-Plastics-and-Laminates-543/202315728 Dremel Cutting / Shaping Wheel] (You will need more than one)
			Here is a photo with the overhead console attached and some paint prep completed.
			[[File:2025-03-18 16.54.47.jpg\|none\|thumb\|Overhead console in place.]]


	=== Notes ===		=== Notes ===
Line 78:		Line 81:
	* Step 5		* Step 5
	** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.		** The kit comes with three 3 inch cutting discs for trimming acrylic ([https://store.vansaircraft.com/norton-cutting-disc-3-tool-3-cutting-disc.html Norton Discs]). You might have to enlarge the very small center hole to make it fit your grinder or to fit into a cut-off disc arbor. High rpms are not necessary for cutting acrylic, an arbor in a standard drill works fine.
	[[Category:Hints]]		[[index.php?title=Category:Hints]]